BMR Suspension
BMR 05-10 S197 Mustang Rear Solid 22mm Sway Bar Kit w/ Bushings & Billet Links - Black Hammertone
BMR 05-10 S197 Mustang Rear Solid 22mm Sway Bar Kit w/ Bushings & Billet Links - Black Hammertone
Couldn't load pickup availability
The two primary functions of sway bars are to control body roll and to determine the understeer or oversteer behavior of a vehicle. Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR Suspension's SB023 rear sway bar was designed by factoring in the vehicle weight, application, motion ratio, coil spring rate, and adjustability requirements. Manufactured from heavy-duty 22mm bar stock, the SB023 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. The SB023 attaches to your Mustang with billet aluminum end links and 88-durometer polyurethane bushings, reducing the deflection from the stock rubber bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing. The CNC-machined, billet aluminum sway bar end links eliminate deflection.
BMR Suspension designed the SB023 sway bar for street performance, autocross, and road race applications. The non-adjustable SB023 gives you a 52% increase in rate over the stock bar (depending on year and model). The rate increases gives you improved handling characteristics so you can drive harder through corners with minimal body roll. This allows for more sway bar control, which equals better handling. When performance is a must, rely on BMR Suspension!
BMR Suspension's SB023 sway bars are available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.!
NOTE: BMR SB023 rear sway bar is not compatible with convertible models unless the additional OE convertible bracing is removed.
Vehicle Fitment
- 2005-2010 Ford Mustang
Please verify exact fitment for your trim and engine before ordering.
Manufacturer Part Number: SB023H
Images are for illustrative purposes only. Actual product may vary.
⚠ WARNING (California Proposition 65): This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
Share
🛡️
Manufacturer's Warranty — BMR Suspension
▾
Manufacturer's Warranty — BMR Suspension
BMR Suspension warrants its products to the original purchaser against defects in materials and workmanship under normal use for two (2) years from the date of sale. BMR's obligation under this warranty is limited to replacement of the product — reinstallation and other incidental costs are not covered — and warranty claims are limited to replacement or credit for returned merchandise. The warranty does not apply to products that have been misused, neglected, altered, damaged or improperly installed, and normal wear is not considered a defect. Impact damage and damage to powder coat are specifically excluded. An RMA is required for all warranty returns; replacement product ships at no charge via UPS Ground, and upgraded shipping is available at the customer's expense for the difference in cost. BMR products are designed for use with OEM and other BMR products — BMR does not warrant fitment with aftermarket products from other manufacturers, including suspension, exhaust, drivetrain or other aftermarket components; returns due to fitment issues with OEM or BMR products receive a full refund, while returns due to fitment issues with another manufacturer's aftermarket parts are subject to a 15% restocking fee. BMR also states that racing parts and equipment are used under varied conditions, that the suitability of any part for a particular application is solely the purchaser's decision, and that BMR makes no warranties, express, implied or written, and that there is no warranty of merchantability; BMR reserves the right to change designs without obligation to modify previously manufactured units, and the buyer agrees to indemnify and hold BMR harmless from any claim arising from installation or use. Separately from warranty, non-warranty returns must be made within 90 days of shipment and carry a 15% restocking fee (shipping costs excluded): items that have been installed, used, modified or damaged are not accepted, everything must come back in its original packaging with an RMA and freight prepaid (collect shipments are refused), any scratch or damage is deducted at the cost to repair or re-powder coat, missing components are deducted at replacement cost, and special order items cannot be returned.
Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by BMR Suspension. Contact us if you need help with a warranty claim.
Q&A
No questions yet. Be the first to ask!