BMR Suspension
BMR 13-15 5th Gen Camaro Front & Rear Sway Bar Kit w/ Bushings - Red
BMR 13-15 5th Gen Camaro Front & Rear Sway Bar Kit w/ Bushings - Red
Couldn't load pickup availability
Reduce body roll and improve the handling of your 2013-2015 Camaro with a Sway Bar Kit from BMR Suspension! Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR’s Sway Bar Kit (SB039) increases sway bar rate over the OE bars and is designed for street performance, autocross, and road racing applications. When performance is a must, rely on BMR Suspension!
- Fits 2012-2015 Chevy Camaro ZL1s
- Fits 2013-2015 Chevy Camaro SS’s
- Includes SB038 (Front) and SB033 (Rear)
- Manufactured from 29mm (Front) and 32mm (Rear) DOM steel tubing
- Designed for 2012-2015 Camaro ZL1s and 2013-2015 Camaro SS’s with FE4 rear suspension
- Greaseable, 88-durometer polyurethane bushings
- Thrust washers allow for proper location of the sway bar and prevent lateral movement
- Cold-formed to better resist torsional fatigue
- 3-hole adjustable front and rear bar
- Increases sway bar rate and allows for fine tuning of your Camaro’s handling characteristics
- Dramatically reduces body roll
- Greater sway bar control allows for better handling of your vehicle
- Available in red or black hammertone powder coat for long lasting good looks
- 3-4 hour installation time
- Proudly designed in the USA!
- Proudly made in the USA!
Please note:
- BMR’s SB039 is not compatible with convertible Camaros or Camaros equipped with V6s due to the SB033 rear bar interfering with the rear V6 brake calipers.
- BMR’s SB033 rear bar inside kit SB039 is designed as a direct replacement for FE4 rear suspension systems where the sway bar end links are located outboard of the rear shocks. This system is included on 2012-2015 ZL1s and 2013-2015 SS’s. 2010-2012 Camaro SS’s may upgrade to this FE4 bar if the rear lower control arms and rear sway bar end links are upgraded to FE4 spec.
Below are rate specs compared to available OE bars: Front (SB038)
- Hole 1 (Boot-leg end of bracket) = 98% increase in sway bar rate
- Hole 2 = 146%
- Hole 3 = 214%
Rear (SB033)
- OE SS Bar (FE4)
o Hole 1 = 100% increase in sway bar rate o Hole 2 = 150% o Hole 3 = 200%
- OE ZL1 Bar (FE5)
o Hole 1 = 25% increase in sway bar rate o Hole 2 = 40% o Hole 3 = 75%
Vehicle Fitment
- 2013-2015 Chevrolet Camaro
Please verify exact fitment for your trim and engine before ordering.
Manufacturer Part Number: SB039R
Images are for illustrative purposes only. Actual product may vary.
⚠ WARNING (California Proposition 65): This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
Share
🛡️
Manufacturer's Warranty — BMR Suspension
▾
Manufacturer's Warranty — BMR Suspension
BMR Suspension warrants its products to the original purchaser against defects in materials and workmanship under normal use for two (2) years from the date of sale. BMR's obligation under this warranty is limited to replacement of the product — reinstallation and other incidental costs are not covered — and warranty claims are limited to replacement or credit for returned merchandise. The warranty does not apply to products that have been misused, neglected, altered, damaged or improperly installed, and normal wear is not considered a defect. Impact damage and damage to powder coat are specifically excluded. An RMA is required for all warranty returns; replacement product ships at no charge via UPS Ground, and upgraded shipping is available at the customer's expense for the difference in cost. BMR products are designed for use with OEM and other BMR products — BMR does not warrant fitment with aftermarket products from other manufacturers, including suspension, exhaust, drivetrain or other aftermarket components; returns due to fitment issues with OEM or BMR products receive a full refund, while returns due to fitment issues with another manufacturer's aftermarket parts are subject to a 15% restocking fee. BMR also states that racing parts and equipment are used under varied conditions, that the suitability of any part for a particular application is solely the purchaser's decision, and that BMR makes no warranties, express, implied or written, and that there is no warranty of merchantability; BMR reserves the right to change designs without obligation to modify previously manufactured units, and the buyer agrees to indemnify and hold BMR harmless from any claim arising from installation or use. Separately from warranty, non-warranty returns must be made within 90 days of shipment and carry a 15% restocking fee (shipping costs excluded): items that have been installed, used, modified or damaged are not accepted, everything must come back in its original packaging with an RMA and freight prepaid (collect shipments are refused), any scratch or damage is deducted at the cost to repair or re-powder coat, missing components are deducted at replacement cost, and special order items cannot be returned.
Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by BMR Suspension. Contact us if you need help with a warranty claim.

Q&A
No questions yet. Be the first to ask!