BMR Suspension
BMR 82-02 3rd Gen F-Body with 3.0-3.25in Axles Rear Hollow 1.375in Xtreme Anti-Roll Kit - Red
BMR 82-02 3rd Gen F-Body with 3.0-3.25in Axles Rear Hollow 1.375in Xtreme Anti-Roll Kit - Red
Couldn't load pickup availability
Hard launches from high horsepower cars at the drag strip require more than just a normal street-style sway bar. BMR's suspensions Xtreme Anti Roll Bar for 1982-2002 GM F-body allows you to launch harder without excessive body roll limiting traction, with little sacrifice to your Camaros street manners. Manufactured from heavy-wall 1.375-inch DOM tubing, BMRs Xtreme Anti Roll Bar (XSB001) is designed to eliminate body roll and transfer as much power as possible to the rear wheels. The XSB001 attaches to your F-body with polyurethane bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing under high compression loads. BMR's suspension designed the XSB001 sway bar for street performance and drag race applications. The large adjustable sway bar has two positions, giving you the versatility to drive to and from the track with the same sway bar. The XSB001 gives you a massive increase in rate over the stock bar (depending on year and model). These rate increases and adjustability allow you to almost eliminate body roll so you can leave the starting line harder with maximum traction. The hollow design gives you loads of strength without adding a lot of weight. When performance is a must, rely on BMR's suspension!BMR's suspensions XSB001 anti roll bar is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.! BMR Suspension designed the XSB001 anti-roll bar for drag race and limited street applications.
- Massive increase in sway bar rate over stock sway bar (depending on year and model)
- Manufactured from 1.375-inch heavy-wall DOM tubing for increased strength
- Designed for street performance and drag race applications
- Adjustability allows for fine-tuning of suspension
- Cold formed to better resist torsional fatigue
- 88-durometer, greasable polyurethane bushings
- Two-way adjustable for street and track use
- Dramatically reduces body roll
- Proudly designed in the U.S.A.
- Fits 3" and 3.25" axle tubes
- 1-2-hour installation time
- Proudly made in the U.S.A.
- Durable powdercoat finish
- Fits 1982-2002 GM F-body
- 100% bolt-in design
Vehicle Fitment
- 1982-2002 Chevrolet Camaro
- 1982-2002 Pontiac Firebird
Please verify exact fitment for your trim and engine before ordering.
Manufacturer Part Number: XSB001R
Images are for illustrative purposes only. Actual product may vary.
⚠ WARNING (California Proposition 65): This product can expose you to chemicals which are known to the State of California to cause cancer and/or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
Share
🛡️
Manufacturer's Warranty — BMR Suspension
▾
Manufacturer's Warranty — BMR Suspension
BMR Suspension warrants its products to the original purchaser against defects in materials and workmanship under normal use for two (2) years from the date of sale. BMR's obligation under this warranty is limited to replacement of the product — reinstallation and other incidental costs are not covered — and warranty claims are limited to replacement or credit for returned merchandise. The warranty does not apply to products that have been misused, neglected, altered, damaged or improperly installed, and normal wear is not considered a defect. Impact damage and damage to powder coat are specifically excluded. An RMA is required for all warranty returns; replacement product ships at no charge via UPS Ground, and upgraded shipping is available at the customer's expense for the difference in cost. BMR products are designed for use with OEM and other BMR products — BMR does not warrant fitment with aftermarket products from other manufacturers, including suspension, exhaust, drivetrain or other aftermarket components; returns due to fitment issues with OEM or BMR products receive a full refund, while returns due to fitment issues with another manufacturer's aftermarket parts are subject to a 15% restocking fee. BMR also states that racing parts and equipment are used under varied conditions, that the suitability of any part for a particular application is solely the purchaser's decision, and that BMR makes no warranties, express, implied or written, and that there is no warranty of merchantability; BMR reserves the right to change designs without obligation to modify previously manufactured units, and the buyer agrees to indemnify and hold BMR harmless from any claim arising from installation or use. Separately from warranty, non-warranty returns must be made within 90 days of shipment and carry a 15% restocking fee (shipping costs excluded): items that have been installed, used, modified or damaged are not accepted, everything must come back in its original packaging with an RMA and freight prepaid (collect shipments are refused), any scratch or damage is deducted at the cost to repair or re-powder coat, missing components are deducted at replacement cost, and special order items cannot be returned.
Warranty terms are set by the manufacturer and may change. Full details and claims are handled directly by BMR Suspension. Contact us if you need help with a warranty claim.
Q&A
No questions yet. Be the first to ask!